How To Reset Outdoor Motion Sensor Lights?

How To Reset Outdoor Motion Sensor Lights

In this post, I will answering your question of how to reset outdoor motion sensor lights.

The outdoor motion sensor lights are an easy way to keep your home safe and secure. The only issue with them is that they can’t be turned off on a timer like the indoor ones. This means you have to remember to turn them off every day during the winter months, otherwise they will burn out! Luckily, there’s a simple solution for this problem!

How To Reset Outdoor Motion Sensor Lights?

Are you tired of your outdoor motion sensor lights not working? It is possible that they need to be reset. Here are some things you can do to make sure they work properly.

1. Check the batteries in the light and replace with fresh ones if needed

First thing you need to do is check your outdoor motion sensor lights batteries. You can replace them with new ones if needed.

Put in new batteries only, do not reuse old batteries for this reason. Batteries can still have a charge even though they are old so putting them back in will cause the light to malfunction again quickly. If you put tired, weak or “just-worked” batteries into an active device it may stop working completely or not work at all until the battery is replaced again. The same goes for flashlights , remotes and other devices that need new batteries to function properly .

To properly reset the motion sensor lights, replacing batteries with fresh ones is the first step.

2. Reset them to factory defaults

Once you have new batteries, click or turn your outdoor motion sensor lights on and off five times within 10 seconds. This will reset the light to its default mode . The motion sensor will now trigger a light when it senses motion again after being reinstalled. If this does not work , proceed to step three .

3. Re-pairing with control panel or transmitter

Press and hold down the button on the control panel for about four seconds until the green LED comes back on indicating that it has been reset (or if solar, let set in full sun for an hour). You should now be able to re-pair your device as usual . Some devices have a small button on the back. Press, hold and release this to reset the device.

4. Replace with a different type of light bulb

Older incandescent bulbs can prevent the motion sensor from working properly . To ensure proper operation in these cases , replace with LED or CFL bulbs that have been specifically designed for use indoors or outdoors in a security light fixture .

Also, to prevent your outdoor lights from not working, make sure to clean all debris and leafs out of the sensor housing. This will allow it to better detect motion .

Remember that the best way to keep your outdoor lights working is by pairing them with a control panel or transmitter which you can find here:

5. Test them regularly

Just to make sure they are working right Make sure you test your motion sensor lights regularly to make sure they still work when you need them most-at night! This will save time and money in case something has happened to one of your outdoor motion sensors while you were not home.

There is one more solution with your motion detector lights if none of these work for you. You can disconnect the light from the outdoor motion detector . Move it near a window or door and install an ordinary wall switch to control it.

You can use this as a manual override of the motion detector when needed .

When all else fails, you will need to replace your old motion sensor lights with new ones. If you have an extremely high-traffic area you should consider changing them every year or so anyway since they do wear out after time.

Why is my motion sensor light not working?

One of the reasons motion sensor light may not be working is because it is too bright. This will cause the sensor to not recognize any motion since it has already detected the light. If this is happening, move your motion sensor lights further away from the area that needs to be lit up . If

you have a large area that needs to be lit, consider using multiple motion sensor lights or an AC powered flood light . These are often brighter than most solar lights. It also helps if all the bulbs have been replaced with LED or CFL bulbs designed for outdoor use.

The other reason is that there may not be enough ambient light in the area where your motion sensor light was installed for it to detect any movement at night . This can happen because of shadows cast by trees and surrounding structures such as buildings and fences near where the light has been installed. The best solution is to reposition your motion sensor system or install more lights so each one will cover a larger area and overlap each other’s detection range . 

Some people like their outdoor lights to come on when they enter their driveway or outdoor spaces . You can achieve this by having two lights installed at different heights pointing at the same area. Each motion sensor light will turn on when motion is detected within its range, but only one light will be triggered at a time. If you need to cover larger areas or want your lights to turn on with any motion, consider getting security floodlight fixtures that are wired directly to your home’s electrical system for full control of all connected lights.

Problems with low battery output

Most solar powered motion sensor lights have batteries designed to last between 6 and 12 months depending on how often they are activated. The lifespan of these batteries decreases over time because there is some leakage even if the system is not being used all the time. This is normal and unavoidable with most solar powered motion sensor lights . If your batteries are not lasting as long as they used to, here are some tips you can try:

1) Test the batteries first

You will need a voltmeter for this. First, make sure that there is no AC power going to your motion sensor light by turning it on manually or disconnecting it from any control panel you may have installed with it . Then test each battery individually by placing a voltmeter across each one’s terminals. If any of them registers close to zero volts, then those batteries need replacing . There is also a chance that if two of these batteries happen to be touching each other during installation, they may have short-circuited. If this is the case, try using two fresh new batteries in place of each shorted one before you install them all together again.

2) Test your good batteries

Sometimes when the voltage output from your batteries is too low it can trigger your motion sensor light’s built-in safety shutoff mechanism which will prevent the system from working until you replace the batteries . To test if this might be happening, use a fresh set of batteries and install them in the same way. Next, go to an area where there are no obstructions or obstacles so that they can receive maximum sunlight for several hours . Once the sun goes down, activate your light manually to see if it comes on. If it does not come on even though the batteries are fresh, then your system’s sensor may be too sensitive for its own good .

3) Test your solar panel

If you’ve already checked for obstructions and there is still not enough sunlight reaching the motion sensor light’s solar panel , you can try moving it to a more optimal location. You also want to make sure that the panel itself is getting access to direct sunlight at all times of day . If this doesn’t work, consider replacing just the solar panels on your motion sensor light with brand new ones. They usually last between 3 and 5 years depending on how many hours they are exposed to each day.

How To Reset Outdoor Motion Sensor Lights

Problems with false triggers or short-circuiting

There are things within your environment like falling leaves or blowing tree branches that can give off the impression of motion. This is especially true when you have an area with less light coverage for your solar panel to absorb . To prevent your system from being triggered too often, adjust its “sensitivity” setting by turning it down lower so that it will only react to larger, more obvious changes in movement instead of small things that are easy to miss. Be aware however that this will increase power consumption because it has to work harder, but shouldn’t be overbearing enough to drain your batteries too quickly .

False triggers can also happen if one or more of your lights gets short-circuited while installing them. It’s important not to mix new and old parts during installation because even brand new parts can come defective right out of the package . If you suspect that this might be happening, switch out each light one at a time and see if the problem goes away. If not, then consider replacing them all together with new ones.

If none of these suggestions work for you, then your system may be suffering from a damaged or corroded battery holder assembly . There isn’t much you can do about this except to replace it altogether.

If the problem still persists, you may need new batteries or want reset your outdoor motion sensor lights initially. Just follow steps 1-3 above and they should work properly again.

Hope this guide about how to fix motion sensor lights was helpful and if you have any questions, don’t hesitate to ask me in comments below!

Please share this article with others so they can also learn how to fix their faulty Outdoor Motion Sensor Lights! Thank You for reading my article :)))

References : How to Reset a Motion Sensor Light

Noah Burns

I am Noah Burns- The Guy behind I will Make You Smart. I love to experiment and test new products with an aim to create informative contents for readers like you. It is my aim to make this site a leading source of information and reviews to help consumers make more informed buying decisions.

Recent Posts